Home›Products›Extenders›2×1 USB-C / HDMI HDBaseT 3.0 Wall Plate Transmitter
TC-WP-SWC-210

2×1 USB-C / HDMI HDBaseT 3.0 Wall Plate Transmitter

USB-C or HDMI at the table, one cable to the display

TC-WP-SWC-210

TC-WP-SWC-210 is a two-input wall-plate transmitter for the meeting table or lectern, in a US 2-gang plate. A laptop connects by USB-C or HDMI, and the plate sends uncompressed 4K @ 60 Hz 4:4:4 (8-bit) over HDBaseT 3.0 to its receiver, TC-RX-100, on one shielded CAT6A cable of up to 40 m. Audio, USB 2.0, RS-232 and power travel on the same cable: the receiver powers the plate over it (PoH+), so the wall needs no adapter for the picture, and the computer at the plate reaches the wired network through its USB connection.

The USB-C input carries video, USB and, with a 20 V / 6 A adapter at the plate (not supplied by TELECIS), laptop charging up to 60 W (use a USB-C cable rated USB 3.2 Gen 1 or above). A room PC on HDMI gets its USB through the USB-B host port. The plate selects the source plugged in last and falls back to the other when it is unplugged; the INPUT button or the RS-232 API chooses by hand, and the DISPLAY button turns the screen on and off over CEC. A separate stereo line input rides to the receiver.

  • USB-C or HDMI — switched automatically · US 2-gang plate
  • 4K60 4:4:4 — 40 m on shielded CAT6A · with USB, control and power
  • PoH+ — powered by the receiver · no adapter at the wall for the picture
  • Up to 60 W — USB-C charging with a 20 V / 6 A adapter, not supplied by TELECIS
Drawings
HDMIUSB-CLINKHDMI INONOFFINPUTDISPLAYLINE IN-PUSB-C INUSB HOST6.0ARS-232+-TXRXG20VHDBT OUTFRONTREAR
Drawn from the production silkscreen · Wall plate, front and rear, shown without the faceplate
TC-WP-SWC-210 outline drawing, 89 × 36.25 × 105.6 mm (W × D × H)

Outline for layout, rack and furniture planning · millimetres, nominal, from the production artwork · connector protrusions, feet and cables not shown · not for manufacture

Shown without the faceplate supplied with it. The side view is the overall envelope: the module's depth behind the mounting frame.

A
Specifications

The section that earns
the premium.

ParameterSpecification
Signal standardHDMI 2.0 (HDMI input)
HDCPHDCP 2.2
Maximum resolutionUp to 4096 × 2160 @ 60 Hz 4:4:4 (8-bit), on HDMI and USB-C
Resolution notes4096 × 2160 at 24 / 30 / 50 / 59.94 / 60 Hz · 3840 × 2160 at 24 / 30 / 60 Hz · PC timings 800 × 600 to 2560 × 1600 at 60 Hz
Bandwidth18 Gbps
HDR4K60 4:2:2 12-bit HDR carried
HDMI audio formatsPCM 2.0 / 5.1 / 7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio, DTS:X — on HDMI and USB-C
Analogue audio inputLINE IN-P: stereo (3.5 mm jack) — passed through to the receiver's LINE OUT-P
TransportHDBaseT 3.0, uncompressed
Transmission distance40 m on CAT6A/7 shielded: 4K60 4:4:4 and 4:2:2 12-bit, with audio, USB 2.0, Ethernet, RS-232 and power together · 70 m at 1080p when the wall plate has its own 20 V supply (not supplied by TELECIS)
Power over the linkPoH+ — the transmitter is powered by the receiver over the HDBaseT cable
Inputs1 × HDMI · 1 × USB-C (video, USB 2.0, charging)
Outputs1 × HDBaseT (RJ45)
USBUSB-C input: USB 2.0 to its own computer; use a USB-C cable rated USB 3.2 Gen 1 or above · USB-B host port: for the computer on HDMI (follows the HDMI input) · with TC-RX-100, throughput about 160 Mbps for isochronous devices (cameras, audio), about 232 Mbps for bulk devices (storage)
Control portsRS-232 (3-pin Phoenix) — API control, command pass-through, firmware · 115200 bps, 8-N-1
Other portsDC 20 V input (2-pin Phoenix) — for USB-C charging; the adapter is not supplied by TELECIS
Control methodsFront-panel INPUT and DISPLAY buttons · RS-232 API
SwitchingAutomatic — the input connected last is selected; if it is unplugged, the other connected input takes over · detection is by the 5 V line, so a source left in standby keeps the input
Firmware updateTransmitter over RS-232; the HDBaseT chipset updates through the receiver
OperationDISPLAY: press to turn the display on · hold 3 s to turn it off
Pairs withTC-RX-100 — HDBaseT 3.0 receiver
Power supplyPoH+ from the receiver · a 20 V / 6 A adapter, not supplied by TELECIS, for USB-C charging and runs beyond 40 m
Power consumption6.6 W max · 71.6 W max while charging a laptop
Dimensions (W × D × H)89 × 36.25 × 105.6 mm (plate 89 wide × 105.6 high; 36.25 deep)
Weight360 g
MountingUS 2-gang wall box, or on a desk
Operating temperature0 to 45 °C
Storage temperature−20 to 70 °C
Humidity10–90 % RH, non-condensing
ESD protection±8 kV air · ±4 kV contact (human-body model)
Installation limitsOn CAT5e/6 with patch cords: 30 m at 4K60 4:4:4 (and 4:2:2 / 4:2:0 36-bit) · patch cords count towards the maximum: at most one at each end, 5 m each · straight-through T568B; shielded CAT6A recommended
ComplianceDesigned for global compliance — CE, FCC, RoHS, and regional certifications, as applicable.
Warranty3 years
In the boxWall-plate transmitter · US 2-gang faceplate with 4 screws · USB-A to USB-B cable (1.5 m) · 3-pin and 2-pin 3.5 mm Phoenix connectors · 4 mounting screws · no power adapter
Every value above is taken from the manufacturer's documentation for this model and matches the TELECIS datasheet. Subject to change without notice.
Specification text for consultants9 clauses · basis of design

Basis of design: TELECIS TC-WP-SWC-210.

  1. General The wall-plate transmitter shall fit a US 2-gang wall box, or sit on a desk, switch 1 × HDMI and 1 × USB-C input, and send HDBaseT 3.0, uncompressed, to its receiver, TC-RX-100.
  2. Video The transmitter shall accept HDMI 2.0, 18 Gbps, HDCP 2.2, up to 4096 × 2160 @ 60 Hz 4:4:4 (8-bit) on HDMI and USB-C, and carry 4K60 4:2:2 12-bit HDR.
  3. Audio The transmitter shall carry PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio and DTS:X on HDMI and USB-C, and pass a stereo line input (3.5 mm) to the receiver's line output.
  4. USB The USB-C input shall carry video, USB 2.0 to its own computer and, with a 20 V / 6 A adapter at the plate (not supplied by TELECIS), laptop charging up to 60 W; a USB-B host port shall serve the computer on HDMI.
  5. Switching and control The transmitter shall select the input connected last and fall back to the other when it is unplugged, with INPUT and DISPLAY buttons (the display on and off over CEC) and an RS-232 API (3-pin Phoenix, 115200 bps, 8-N-1).
  6. Transmission The kit shall reach 40 m on CAT6A/7 shielded cable at 4K60 4:4:4, with audio, USB 2.0, Ethernet, RS-232 and power together; 70 m at 1080p when the transmitter has its own 20 V supply; 30 m on CAT5e/6 with patch cords.
  7. Power The transmitter shall be powered by the receiver over the cable (PoH+), at 6.6 W max; USB-C charging shall need a 20 V / 6 A adapter, not supplied by TELECIS (71.6 W max while charging).
  8. Physical The transmitter shall measure 89 × 36.25 × 105.6 mm (plate 89 wide × 105.6 high, 36.25 deep) and weigh 360 g.
  9. Environmental The transmitter shall operate at 0 to 45 °C, be stored at −20 to 70 °C, and tolerate 10–90 % RH, non-condensing.

Written to paste into a project specification; every clause is taken from the manufacturer's documentation behind this page. Check the datasheet revision before issue.

B
Documents

Engineering documentation,
plainly accessible.

C
Within the family

Specified as a system.

D
Specifying this model

Where it belongs.

For the meeting table, lectern or credenza where the presenter arrives with a laptop. The plate takes USB-C or HDMI and puts the picture, USB for the room's camera and speakerphone, the network, control and its own power on one shielded CAT6A run to the display. Specify it with TC-RX-100: the pair is one system, and the receiver's supply runs both ends.

Plan the run to 40 m: that is the reach of the whole system — picture, USB, control and the power that runs the plate. At 1080p, a plate with its own 20 V supply reaches 70 m (the adapter is not supplied by TELECIS).
Specifying for a project?

Where to buy.

TELECIS is sold through authorised regional partners, and directly by the TELECIS specification desk where no partner is appointed. Write with the model and the project.