Home›Products›Extenders›4K60 HDBaseT 3.0 Receiver with USB, Ethernet and PoH+
TC-RX-100

4K60 HDBaseT 3.0 Receiver with USB, Ethernet and PoH+

The display end of the wall-plate kit: picture, USB, network and power

The code is as printed on the unit; the kit's reach is 40 m.

TC-RX-100

TC-RX-100 is the HDBaseT 3.0 receiver for the TC-WP-SWC-210 wall plate. From one shielded CAT6A cable of up to 40 m it delivers uncompressed 4K @ 60 Hz 4:4:4 (8-bit) to the display on HDMI, with USB 2.0, Ethernet, audio and control on the same cable. Its 20 V supply powers the wall plate over that cable (one-way PoH+), so the table end needs no adapter for the picture; laptop charging at the plate needs a 20 V / 6 A adapter there, not supplied by TELECIS.

At the display it serves the room. Three USB 2.0 device ports, two USB-A and one USB-C, take the camera or speakerphone for the computer on the plate's selected input, and an Ethernet port gives the presenter's laptop the wired network through its USB connection. The HDMI signal's audio is de-embedded to one 3.5 mm output, and the plate's line input arrives on another. EDID and the RS-232 mode are set by DIP switch.

  • 4K60 4:4:4 — 40 m on shielded CAT6A · with USB, network and power
  • PoH+ — powers the wall plate over the cable
  • USB 2.0 — two USB-A and one USB-C device ports
  • RJ45 — Ethernet for the laptop at the plate
Drawings
ETHERNETAUDIO OUTHDMI OUTHDBT INRS23220V3.0AGRXTXPOWERLINKVIDEOSETUPDOWNLINE OUT-P123USB DEVICE (2.5A)RECEIVER
Drawn from the production silkscreen · Receiver, top, with the end faces unfolded
TC-RX-100 outline drawing, 212.5 × 110 × 25 mm (W × D × H)

Outline for layout, rack and furniture planning · millimetres, nominal, from the production artwork · connector protrusions, feet and cables not shown · not for manufacture

The supplied mounting brackets are not shown; on its feet the unit stands 27.3 mm high.

A
Specifications

The section that earns
the premium.

ParameterSpecification
HDCPHDCP 2.2 with TC-WP-SWC-210 · the receiver itself: HDCP 2.3 / 2.2 / 1.4
Maximum resolution4096 × 2160 @ 60 Hz 4:4:4 (8-bit)
Bandwidth18 Gbps
HDR4K60 4:2:2 12-bit HDR carried from TC-WP-SWC-210 (its documentation names no HDR formats) · the receiver itself accepts HDR10, HDR10+, HLG and Dolby Vision
HDMI audio formatsWith TC-WP-SWC-210: PCM 2.0 / 5.1 / 7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio, DTS:X · the receiver itself takes up to 7.1, adding Dolby Digital, Dolby Digital Plus and DTS 5.1
Audio de-embeddingAUDIO OUT: stereo, 3.5 mm — de-embedded from the HDMI signal
Analogue audio outputLINE OUT-P: stereo, 3.5 mm — the wall plate's LINE IN-P, passed through
Analogue performance2 Vrms · SNR > 85 dB · THD+N < 0.05 % at 1 kHz · crosstalk > 60 dB (20 Hz–20 kHz)
TransportHDBaseT 3.0, uncompressed
NetworkEthernet over the link, for the computer at the transmitter — works only with the transmitter
Transmission distance40 m on CAT6A/7 shielded: 4K60 4:4:4 and 4:2:2 12-bit, with audio, USB 2.0, Ethernet, RS-232 and power together · 70 m at 1080p when the wall plate has its own 20 V supply (not supplied by TELECIS)
Power over the linkSupplies the transmitter — one-way PoH+, IEEE 802.3at: up to 30 W out, up to 25.5 W at the transmitter
Inputs1 × HDBaseT (RJ45)
Outputs1 × HDMI · 2 × stereo 3.5 mm (LINE OUT-P, AUDIO OUT)
USB2 × USB-A + 1 × USB-C device ports, USB 2.0 · 2.5 A shared · one hub tier · throughput about 160 Mbps for isochronous devices (cameras, audio), about 232 Mbps for bulk devices (storage)
Network ports1 × RJ45 Ethernet
Control portsRS-232 (3-pin 3.5 mm Phoenix) — pass-through, and firmware update
Other portsDC 20 V locking input
Control methodsNo control interface of its own: 4-way DIP switch for EDID and the RS-232 mode · RS-232 pass-through
EDID managementDIP switch: copy from the display (default), or fixed 4K60, 4K30 or 1080p60 with 2-channel PCM
Firmware updateRS-232, mode set by DIP switch — receiver and HDBaseT chipset
Pairs withTC-WP-SWC-210 — US 2-gang wall-plate transmitter
Power supply20 V DC, 3 A locking adapter (in the box) — also powers the wall plate over the cable; the plate's USB-C charging needs its own 20 V / 6 A adapter, not supplied by TELECIS
Dimensions (W × D × H)212.5 × 110 × 25 mm (mounting ears extra) · 27.3 mm high on its feet
HousingSheet steel
MountingMounting brackets (4 in the box)
Operating temperature0 to 50 °C
Storage temperature−20 to 60 °C
Humidity20–90 % RH, non-condensing
ESD protection±8 kV air · ±4 kV contact (human-body model)
Installation limitsOn CAT5e/6 with patch cords: 30 m at 4K60 4:4:4 (and 4:2:2 / 4:2:0 36-bit) · patch cords count towards the maximum: at most one at each end, 5 m each · straight-through T568B; shielded CAT6A recommended
ComplianceDesigned for global compliance — CE, FCC, RoHS, and regional certifications, as applicable.
Warranty3 years
In the boxReceiver · 20 V / 3 A adapter · 4 mounting brackets with screws · 3-pin 3.5 mm Phoenix connector
Every value above is taken from the manufacturer's documentation for this model and matches the TELECIS datasheet. Subject to change without notice.
Specification text for consultants9 clauses · basis of design

Basis of design: TELECIS TC-RX-100.

  1. General The receiver shall receive HDBaseT 3.0, uncompressed, from TC-WP-SWC-210 and deliver HDMI, USB 2.0, Ethernet and audio at the display, powering the transmitter over the same cable.
  2. Video The receiver shall output up to 4096 × 2160 @ 60 Hz 4:4:4 (8-bit), 18 Gbps, with HDCP 2.2 when paired with TC-WP-SWC-210, and carry 4K60 4:2:2 12-bit HDR from it.
  3. Audio The receiver shall de-embed the HDMI audio to a stereo 3.5 mm output and pass the transmitter's line input to a second stereo 3.5 mm output, at 2 Vrms, SNR > 85 dB and THD+N < 0.05 % at 1 kHz.
  4. USB and network The receiver shall provide 2 × USB-A and 1 × USB-C USB 2.0 device ports (2.5 A shared, one hub tier) and 1 × RJ45 Ethernet port for the computer at the transmitter.
  5. Control The receiver shall set EDID (copy from the display, or fixed 4K60, 4K30 or 1080p60 with 2-channel PCM) and the RS-232 mode by DIP switch, and pass RS-232 (3-pin 3.5 mm Phoenix).
  6. Transmission The kit shall reach 40 m on CAT6A/7 shielded cable at 4K60 4:4:4, with audio, USB 2.0, Ethernet, RS-232 and power together; 70 m at 1080p when the transmitter has its own 20 V supply; 30 m on CAT5e/6 with patch cords.
  7. Power The receiver shall use a 20 V DC, 3 A locking adapter and supply the transmitter by one-way PoH+ (IEEE 802.3at; up to 30 W out, up to 25.5 W at the transmitter).
  8. Physical The receiver shall measure 212.5 × 110 × 25 mm (mounting ears extra), in a sheet-steel housing, with 4 mounting brackets.
  9. Environmental The receiver shall operate at 0 to 50 °C, be stored at −20 to 60 °C, and tolerate 20–90 % RH, non-condensing.

Written to paste into a project specification; every clause is taken from the manufacturer's documentation behind this page. Check the datasheet revision before issue.

B
Documents

Engineering documentation,
plainly accessible.

C
Within the family

Specified as a system.

D
Specifying this model

Where it belongs.

At the display, where the room's camera, speakerphone and network meet the presenter's laptop. The receiver powers the wall plate over the cable and hands the laptop the room's USB devices and the wired network, so the table end needs nothing but the cable; laptop charging at the plate needs the plate's own 20 V / 6 A supply.

USB 2.0 runs at about 160 Mbps for cameras and audio devices: confirm the camera's USB mode before it is specified.
Specifying for a project?

Where to buy.

TELECIS is sold through authorised regional partners, and directly by the TELECIS specification desk where no partner is appointed. Write with the model and the project.