Home›Products›Extenders›4K60 HDMI Extender (70m)
TC-EXT-70

4K60 HDMI Extender (70m)

70 m over CAT6/6A, without touching the picture

TC-EXT-70

TC-EXT-70 carries HDMI 2.0b across up to 70 m of a single CAT6/6A cable, uncompressed and without added latency: 4K @ 60 Hz with full 4:4:4 colour, and HDR10, HDR10+, Dolby Vision and HLG passed through. HDCP 2.2 is maintained end to end, and one 12 V supply at either end powers both units over the same cable.

Control and audio travel with the picture. Infrared passes in both directions, so source and display can be operated from either end. The receiver's TOSLINK output feeds an amplifier with the programme audio or, with ARC enabled, the sound returning from the display. EDID is set on the transmitter by DIP switch — copied from the far display or the local loop-out, or fixed at 4K60 or 1080p stereo.

  • 70 m — over one CAT6/6A cable
  • 4K60 4:4:4 — HDMI 2.0b · 18 Gbps · HDCP 2.2
  • HDR — HDR10 · HDR10+ · Dolby Vision · HLG
  • PoC — power over cable · one 12 V supply for the pair
Drawings
TransmitterEDIDDC 12VIR OUTIR INSERVICEOUTCAT OUTINReceiverARCDC 12VIR OUTIR INSERVICEOUTCAT INTOSLINKTRANSMITTERRECEIVER
Drawn from the production silkscreen · Transmitter and receiver, top, side and both ends
TC-EXT-70 outline drawing, 90 × 68 × 18 mm (W × D × H)

Outline for layout, rack and furniture planning · millimetres, nominal, from the production artwork · connector protrusions, feet and cables not shown · not for manufacture

Signal path
SOURCEHDMITXTRANSMITTERCAT6/6A · UP TO 70 mVIDEO · AUDIOIR BOTH WAYSPoC · 12 V AT EITHER ENDRXRECEIVERHDMIDISPLAYHDMI LOOP-OUTLOCAL MONITORTOSLINKAMPLIFIERPROGRAMME AUDIO, OR ARC FROM THE DISPLAY
one CAT6/6A run carries video, audio, IR and power
A
Specifications

The section that earns
the premium.

ParameterSpecification
Signal standardHDMI 2.0b
HDCPHDCP 2.2
Maximum resolutionUp to 4K @ 60 Hz, RGB / YCbCr 4:4:4
Bandwidth18 Gbps
Colour spaceRGB 4:4:4 · YCbCr 4:4:4 / 4:2:2 / 4:2:0
Colour depth8/10/12-bit
HDRHDR10, HDR10+, Dolby Vision, HLG
HDMI audio formatsLPCM 7.1, Dolby TrueHD, DTS-HD Master Audio
Audio de-embeddingReceiver TOSLINK output: Dolby 5.1, DTS 5.1, PCM 2.0
Audio returnARC — audio from the display at the receiver leaves on the receiver's TOSLINK (DIP-selectable)
TransportUncompressed, zero-latency HDMI over one CAT cable (point to point)
Transmission distance70 m at 4K60 4:4:4 and at 1080p, over CAT6/6A
Power over the linkBi-directional PoC — one 12 V supply at either end powers both
InputsTransmitter: 1 × HDMI · Receiver: 1 × CAT (RJ45)
OutputsTransmitter: 1 × HDMI loop-out + 1 × CAT (RJ45) · Receiver: 1 × HDMI + 1 × TOSLINK
Control portsEach end: IR in, IR out (3.5 mm), micro-USB service port
Control methodsIR pass-through (no RS-232)
EDID managementDIP switch on the transmitter: copy from the display at the receiver · 4K60 stereo · 1080p stereo · copy from the local loop-out display
IRBi-directional IR, wideband 20–60 kHz, 5 Vp-p
Power supply12 V DC, 1 A locking adapter
Power consumption3.36 W max
Dimensions (W × D × H)90 × 68 × 18 mm (each unit)
WeightTransmitter 160 g · receiver 155 g
HousingMetal, black
Operating temperature0 to 40 °C
Storage temperature−20 to 60 °C
HumidityOperating 20–80 % · storage 10–90 % RH, non-condensing
ESD protection±8 kV air · ±4 kV contact (IEC 61000-4-2)
ComplianceDesigned for global compliance — CE, FCC, RoHS, and regional certifications, as applicable.
Warranty3 years
In the boxTransmitter · receiver · IR blaster cable (1.5 m) · wideband IR receiver cable (1.5 m) · 4 mounting ears · 8 screws · 12 V / 1 A locking adapter
Kit compositionSold as a kit — transmitter + receiver
Every value above is taken from the manufacturer's documentation for this model and matches the TELECIS datasheet. Subject to change without notice.
Specification text for consultants9 clauses · basis of design

Basis of design: TELECIS TC-EXT-70.

  1. General The extender shall be a transmitter and receiver kit carrying uncompressed, zero-latency HDMI point to point, 70 m over a single CAT6/6A cable at 4K60 4:4:4 and at 1080p.
  2. Video The extender shall support HDMI 2.0b, 18 Gbps and HDCP 2.2 up to 4K @ 60 Hz 4:4:4, with HDR10, HDR10+, Dolby Vision and HLG pass-through.
  3. Colour The extender shall support deep colour up to 12-bit (8/10/12-bit).
  4. Audio The extender shall carry LPCM 7.1, Dolby TrueHD and DTS-HD Master Audio; the receiver's TOSLINK output shall carry de-embedded Dolby 5.1, DTS 5.1 or PCM 2.0, or the display's ARC audio.
  5. Control The extender shall pass bi-directional IR (no RS-232), with EDID set by DIP switch: copied from either display, or fixed at 4K60 or 1080p stereo.
  6. Connections The transmitter shall provide 1 × HDMI input, 1 × HDMI loop-out and 1 × CAT (RJ45); the receiver 1 × CAT (RJ45), 1 × HDMI and 1 × TOSLINK; each end IR in and out (3.5 mm).
  7. Power The pair shall run on bi-directional PoC from one 12 V DC, 1 A locking adapter at either end, at 3.36 W max.
  8. Physical Each unit shall measure 90 × 68 × 18 mm (W × D × H); the transmitter shall weigh 160 g and the receiver 155 g.
  9. Environmental The extender shall operate at 0 to 40 °C and 20–80 % RH, non-condensing, and be stored at −20 to 60 °C.

Written to paste into a project specification; every clause is taken from the manufacturer's documentation behind this page. Check the datasheet revision before issue.

B
Documents

Engineering documentation,
plainly accessible.

C
Within the family

Specified as a system.

D
Specifying this model

Where it belongs.

Seventy metres is the distance most rooms actually need — a lectern to a rack, a rack to a projector across a ceiling void. This is the plain, correct answer for that run: full 4K @ 60Hz 4:4:4 over CAT6/6A, EDID set by DIP switch on the transmitter, and IR carried both ways so the far-end display can still be controlled. It has no RS-232 path: where the display needs serial control, specify TC-EXTU-100.

Reach assumes solid-core CAT6/6A, directly terminated. Patch panels and stranded leads subtract from the figure.
Specifying for a project?

Where to buy.

TELECIS is sold through authorised regional partners, and directly by the TELECIS specification desk where no partner is appointed. Write with the model and the project.