An HDMI source into software — over USB-C, or across the network
Formerly listed as TC-CAP-U3.
TC-USBC-CAPTURE takes an HDMI 1.4a source at up to 4K @ 30 Hz and delivers it to a computer over USB-C as a standard UVC video device, or to the network as NDI HX — one or the other at a time. It also accepts 720p50, 1080p50, 1080i50 and 2160p25. Over USB 3.0 it streams MJPEG, H.264 or H.265 to 4K30, or NV12 to 1080p30; on the network, NDI HX runs at 4K30, 1080p60 or 720p60 and works with NDI Tools, OBS and vMix.
An HDMI loop-out keeps the picture on the local display and can show the unit's status on screen. The unit is powered by PoE (IEEE 802.3af) alone, from the network switch or an injector, and its USB-C port supplies 5 V at up to 1 A to the connected computer or drive. Audio is PCM 2.0 on all three outputs. HDCP is not supported: protected sources are neither captured nor passed to the loop-out. Settings and firmware are managed from the web UI or the API.
Outline for layout, rack and furniture planning · millimetres, nominal, from the production artwork · connector protrusions, feet and cables not shown · not for manufacture
| Parameter | Specification |
|---|---|
| Signal standard | HDMI 1.4a in and loop-out |
| HDCP | Not supported — protected sources are neither captured nor passed to the loop-out |
| Maximum resolution | Input up to 4K @ 30 Hz, 4:4:4, 8-bit |
| Resolution notes | Input timings: 640 × 480, 800 × 600, 1024 × 768 and 720 × 576 at 60 Hz · 720p60 · 1080p60 · 3840 × 2160 at 30 Hz · 50 Hz too: 720p50, 1080p50, 1080i50, 2160p25 · in USB 2.0 mode, NV12 at 1080p30 and 720p30 is not available |
| Compression / codec | NDI HX (H.264 / H.265, 4:2:0 8-bit): 4K30, 1080p60, 720p60 · USB 3.0 (UVC): MJPEG, H.264, H.265 to 4K30; NV12 to 1080p30 |
| CEC | Not supported on the loop-out |
| Other audio formats | PCM 2.0 on HDMI, NDI and USB |
| Network | NDI HX over 1G Ethernet |
| Inputs | 1 × HDMI |
| Outputs | 1 × HDMI loop-out (with on-screen status) · USB-C (UVC) or network (NDI HX), one at a time |
| USB | USB-C · USB 3.0 (5 Gbps) or USB 2.0 · supplies 5 V / 1 A to the connected host or drive |
| Control methods | Web UI and API (configuration and firmware) |
| Power supply | PoE only (IEEE 802.3af) |
| Power consumption | 8 W max (without USB load) |
| Dimensions (W × D × H) | 78 × 108.4 × 20 mm |
| Housing | Aluminium |
| Operating temperature | 0 to 45 °C |
| Storage temperature | −20 to 70 °C |
| Humidity | 10–90 %, non-condensing |
| ESD protection | ±8 kV air · ±4 kV contact (human-body model) |
| Compliance | Designed for global compliance — CE, FCC, RoHS, and regional certifications, as applicable. |
| Warranty | 3 years |
| In the box | Capture unit · 1.8 m USB 3.0 Type-A to USB-C cable |
Basis of design: TELECIS TC-USBC-CAPTURE.
Written to paste into a project specification; every clause is taken from the manufacturer's documentation behind this page. Check the datasheet revision before issue.
A capture device earns its place by being boring to IT. This one presents to the computer as a standard UVC video device and works with NDI Tools, OBS and vMix, so it survives the laptop refresh that breaks proprietary capture. HDMI loops through for the local display, and NDI HX over the network is available where the destination is a production system rather than a laptop.
TELECIS is sold through authorised regional partners, and directly by the TELECIS specification desk where no partner is appointed. Write with the model and the project.