Home›Journal›What IPMX certification leaves to the buyer
STANDARDS · 2 October 2026 · 5 min read

What IPMX certification leaves to the buyer.

IPMX certification records what was tested. The decisions it leaves to the buyer — profile per position, network class, PTP, and what a listing does not cover — decide whether a multi-vendor system works.

JOURNAL / 016
FOUR DECISIONS PER POSITION01 · PROFILE02 · NETWORK03 · TIMING04 · CHECK SEPARATELYJPEG XSTDC MODE OPTIONAL4K60 ON A SINGLE 1G LINKAIMS FIGURE · STATE THE BIT RATEUNCOMPRESSED VIDEOTR-10-2≈10.6 GBIT/S AT 2160P59.944:2:2 10-BIT · 25G-CLASS LINKPCM AUDIOTR-10-3AUDIO ENDPOINTSBASELINE + THIS PROFILE CERTIFIESPTP OPTIONAL · PRESENT: SENDERS USE IT · ABSENT: FREE-RUNNING CLOCK · STATE WHICHHKEP · PEPLISTED SEPARATELYUSB · H.264 · H.265STILL DRAFT AT VSFFIRMWAREDECLARED AT TESTTHE REGISTER SAYS WHAT WAS TESTED — THE SPECIFICATION SAYS WHAT EACH POSITION NEEDS
Profile, network, timing, and the items to check separately — decided per position, then written into the specification.

IPMX certification tells a buyer what an independent test proved about a product. It leaves the system decisions with the buyer: which profile each position needs, what network that profile implies, whether the design runs PTP, and which features a listing does not cover. Those decisions, not the logo, decide whether a certified encoder and a certified decoder will share a stream.

The background — what IPMX is assembled from, how the independent testing works, and why a public register beats an adjective — is in Interoperability you can look up. In short, the first certification round, tested in January, was announced at ISE in February, and a second at the start of September.

Which IPMX profile does each position need?

To be listed, a product must pass the IPMX baseline and at least one profile: uncompressed video, PCM audio or JPEG XS. Further profiles and optional capabilities are tested and listed individually, so the first decision is made per position, not per project.

JPEG XS is the profile for 4K on existing infrastructure: AIMS lists 4K60 over a single gigabit network among IPMX's features. The codec is built for an end-to-end latency of a few lines, at compression ratios typically up to 10:1. The profile only requires a sender to reach 4 bits per pixel, about 2 Gbit/s at 2160p60, so a 1G design must state the bit rate and confirm the sender reaches it. Every receiver certified to the IPMX JPEG XS profile must accept both formats a sender may use — 10-bit 4:2:2 YCbCr and 8-bit 4:4:4 RGB. TDC (temporal differential coding) is an optional mode that exploits the redundancy between successive frames, especially in static regions; a TDC sender must also support the base profile, so specify TDC only where both ends are listed for it.

Uncompressed video is for paths where compression itself is the risk, and it changes the network. PCM audio covers audio endpoints; a device can be certified on the baseline and that profile alone.

A receiver listed only for uncompressed video will not take a JPEG XS stream, however certified both ends are. The trade between JPEG XS and other intra-frame codecs is set out in Two ways to be visually lossless.

What network does each profile need?

For JPEG XS, the gigabit figure is AIMS's. For uncompressed video, the arithmetic is unforgiving. An ST 2110 tutorial published by AIMS puts 1080p59.94 at 4:2:2 10-bit at 2.65 Gbit/s on the wire, so three such streams fit within a 10G port. 2160p has four times the pixels: about 10.6 Gbit/s, more than a 10G port carries, which makes uncompressed 4K a 25G-class design. Choose the profile first; the switch follows from it.

Does an IPMX design need PTP?

No — but it needs a decision. Under VSF TR-10-1, a sender uses the PTP common reference clock when the network has one and a free-running internal clock when it does not, and asynchronous sources are supported. Media that must be frequency- and phase-aligned, which TR-10-1 calls sync media, needs that common clock. A presentation-led estate can run without a grandmaster; one that must stay aligned with ST 2110 production, where timing is PTP-based, will need one. State which in the design, because senders behave differently in the two cases.

What does a certification listing not cover?

Optional capabilities. HKEP (HDCP key exchange) and PEP (privacy encryption) are listed separately, and failing an optional capability does not affect certification status. Wherever an HDCP source will be routed, check that both ends are listed for HKEP.

Parts still in draft. The VSF still publishes IPMX's USB part (TR-10-14) and its H.264 and H.265 parts as drafts, and the capabilities tested in the round announced in September were HKEP and PEP. A room that depends on USB extension over the network should not assume a listing includes it.

The firmware you install. Manufacturers must declare the firmware version tested. Ask for it, and agree how a later version will be treated.

Installed systems. A proprietary AV-over-IP estate that works today keeps working; certifying other products does not touch it.

When is a proprietary JPEG 2000 system at 1G still the sensible choice?

When the estate is closed — one manufacturer, existing gigabit switches, no need to exchange streams with other vendors' equipment or a production plant — or when the room depends on something a listing does not yet cover, such as USB extension. The cost is interoperability with everyone else, which is exactly what IPMX offers, so make the choice knowingly and record it. Mixed estates are legitimate: IPMX where streams must cross vendor lines, a proprietary system where they need not, with the boundary drawn in the design rather than discovered on site. TELECIS's current networked range is JPEG2000 over 1G and is not IPMX certified.

How do you write it into a specification?

Requiring a registry listing is the start. Then name, per position:

  • Profile: JPEG XS (stating the maximum bit rate per stream and whether TDC mode is required), uncompressed video or PCM audio.
  • Capabilities: HKEP wherever an HDCP source is routed; PEP where streams must be encrypted on a shared network.
  • Firmware: the version declared at testing, and the rule for later versions.
  • Network and control: link rate per profile, whether PTP will be present, and who supplies the NMOS controller and, if one is used, the registration service.

Treat “IPMX compatible” in a submittal as a question: programme rules bar uncertified products from using the IPMX name or logo, though they may say they conform to VSF TR-10. The register says what was tested; the specification has to say what each position needs.

Questions, answered briefly

Which IPMX profile should I specify for 4K60 on a gigabit network?
JPEG XS. AIMS lists 4K60 over a single gigabit network among IPMX's features, while uncompressed 2160p59.94 at 4:2:2 10-bit needs about 10.6 Gbit/s on the wire. The profile only requires a sender to reach 4 bits per pixel, about 2 Gbit/s at 2160p60, so state the bit rate the link allows and confirm the sender supports it. Check that both the sender and the receiver are listed for the JPEG XS profile, and for TDC mode if you require it.

Does an IPMX system need PTP?
No. Under VSF TR-10-1, an IPMX sender uses the PTP common reference clock when one is present on the network and a free-running internal clock when it is not. The design should still state which applies, and media that must be frequency- and phase-aligned needs the common clock.

Does IPMX certification guarantee HDCP and USB support?
No. HDCP key exchange (HKEP) is an optional capability that is tested and listed separately, and failing it does not affect certification status, so check the listing wherever an HDCP source will be routed. USB extension is defined in VSF TR-10-14, which is still published as a draft.

What is the difference between “IPMX certified” and “conforms to TR-10”?
Under the programme rules, only certified products may use the IPMX name or logo. Vendors of uncertified products may say they conform to the VSF TR-10 specifications but must not imply IPMX certification, so ask for the registry listing.

Published by TELECIS · 2 October 2026 · Filed under Standards
Specifying?

Send the room.

We return the architecture, the bill of materials, and the route to supply.